Products

Features Used to join Romex low voltage lead to low voltage power line connector or interconnector Compatible Fixtures  (Sold Separately): T...

Features Length: 24" Finish: Black, White 2 foot Plastic Wire Raceway – Field cuttable – Includes wire channel with double faced tape and cover...

Pair of two mounting clips for 120V LED Tape Light. Each 12″ section of tape light includes two mounting clips. Features Sold in pack of 2 Two Mou...

L Connector connects two COB LED tape lights together at a 90° angle. Easily insert the tape light section into the connector without any tools nee...

T Connector connects three COB LED tape lights together. Easily insert the tape light section into the connectors without any tools needed. Feature...

X Connector connects four COB LED tape lights together. Easily insert the tape light section into the connectors without any tools needed. Features...

A 3″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed...

A 6" Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed...

The end-to-end connector connects two RGBW COB LED tape lights seamlessly. Maximum run length for tape light is 16.4′. Features Connects two tape ...

12″ Cable used to hardwire RGBW COB LED tape light to a compatible RGBW controller or DMX decoder. Features 12" Cable used to hardwire tape light ...

(15) Clear mounting clips and screws to mount RGBW tape light to flat surface. Note: Pack of 32 are included with each RGBW COB LED Tape Light Roll...

A 18″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools neede...

A 36″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools neede...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...

The end-to-end connector is used to connect two COB LED tape lights. Features Connects two tape light sections together Maximum run length for tap...

12" Hardwire Power Cord for NUTP14 COB Tape Light Features Used to hardwire COB LED tape light to a compatible 24VDC LED driver Dimensions Size:...

A power cord connects the tape light to a compatible 24VDC LED driver with a DC connector. Features Used to hardwire COB LED tape light to a compa...

(15) Clear mounting clips and screws to mount COB LED tape light to a flat surface. Note: A pack of 32 is included with each COB LED Tape Light Rol...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...

The terminal block connects the COB LED tape light to (2) wires (18AWG max.). Can be used as a power feed or jumper. Features Terminal block used ...

The terminal block connects the COB LED tape light to (2) 60″ 18AWG wires. Can be used as a power feed or jumper. Features Terminal block used to ...

The terminal block connects two COB LED tape lights end-to-end. Features Terminal block used to connect two tape light sections together Compatib...

4″ Decorative metal ring changes the appearance of the LED luminaire. Features Finish: Black, Brushed Nickel Compatible Fixture (Sold Separate...

6″ Decorative metal ring changes the appearance of the LED luminaire. Features Finish: Black, Brushed Nickel, Warm White Compatible Fixture (S...

Features New construction frame-in can be used to assist installing can-less recessed downlighting. Helps indicate wiring location and cutting ...

New construction frame-in with collar for 2″ M2 LED Recessed Series. Used for pre-wiring and easier layout planning. Features Mounting: Bar hanger...

4" FLAT wafer can-less LED downlights feature a non-metallic trim for corrosive environments. Can-less downlights are easy to install in new constr...

Dedicated remodel housing for use in insulated ceilings can be in direct contact with insulation. Air-tight construction provides energy savings by...

Suction cup assist removing trimless reflector from finished ceiling after installation. For maintenance on trimless reflector. Features Assist re...

Metal decorative rings changes the appearance of the LED luminaire. Rings are held in place with integral magnets and seamless appearance with no v...

Features ELO can be mounted to a 5″ or 6″ recessed housings with torsion springs brackets using optional torsion spring kit. Compatible Fixtu...

Metal decorative rings changes the appearance of the LED luminaire. Rings are held in place with integral magnets and seamless appearance with no v...

Metal decorative rings changes the appearance of the LED luminaire. Rings are held in place with integral magnets and seamless appearance with no v...

Wire Harness Kit for Multi-Directional Power (pendant mount only) Features Allows pendant mounted NLUD system to be fed in the middle of a run Rep...

Daisy chain bracket for connecting two NLUD luminaires together when wall mounted. Features Finish: Aluminum, Black, White Daisy chain bracket for...

An extension cable is used to extend the length between the luminaire (NM1-170) and a compatible 12V LED driver. Cables can be connected together t...

Features For new construction pre-wiring and easier layout planning Compatible Fixture (Sold Separately): Recessed Downlight: NM1-170 Doc...

Features 24″ Hardwire Power Feed used to connect (1) NM1 LED module to a 12V LED driver. (1) Included with 12W Driver (NM1-DVR12), Splitter Cable ...

Features Converts the round downlight included with 1″ M1+ LED downlight into a square downlight Finish: Black, Bronze, Matte Powder White Di...

Features Round scoop stainless steel trim for NM1-170. Easy install to threaded LED module, no tools are required Finish: Black, White Compat...

Features Round hexcell louver, field changeable trim. Requires NM1-170 Finish: Black, Brushed Nickel, White Compatible Fixture (Sold Separate...

Features Round louver stainless steel, field changeable trim. Requires NM1-170 Finish: Black, Brushed Nickel, White Compatible Fixture (Sold S...

Features Round stainless steel trim for NM1-170. Easy install to threaded LED module, no tools are required Finish: White Compatible Fixture ...