Productos

The 36″ interconnection cable allows for the linking of any two CCT Tape Light runs in any direction. Interconnection cables can be joined together...

Required for each 24V RGB LED Tape Light run. Features A controller is required for each RGB LED tape light run Input Wire: 9-1/2" (10-ft NARGB-76...

Used to mount Tape Light. Includes screws.  Features Sold in pack of 15 Pack of 15 clear acrylic mounting clips are included with every Tape Ligh...

Features Splits power line connector from LED drivers into two separate leads, requires power line cable Voltage: 12V or 24V Finish: White ...

Use to seal connection made in the field. Sold in pack of 5. Features Sold in pack of 5 Two shrink wrap tubes are included with every Tape Light r...

Features Finish: White Used to cover open end of Tape Light. Compatible Fixtures (Sold Separately): LED Tape Light: NUTP10-WCCT/4 , NUTP10-WCCT/...

Features Finish: White Plastic wire J-clips for cable management Pack includes 10 total Compatible Fixture (Sold Separately): LED Tape Light...

Features Finish: White Plastic over the wire clips for cable management Pack includes 10 total Compatible Fixture (Sold Separately): LED Ta...

Features Finish: White Plastic square wire clips for cable management Pack includes 10 total Compatible Fixture (Sold Separately): LED Tape...

Features Finish: Black Terminal Block for connecting low voltage wires together. 4-in / 4-out Compatible Fixture (Sold Separately): LED ...

Features Finish: Black Terminal Block for connecting low voltage wires together. 8-in / 8-out Compatible Fixture (Sold Separately): LED ...

Features Used to join Romex low voltage lead to low voltage power line connector or interconnector Compatible Fixtures  (Sold Separately): T...

Features Length: 24" Finish: Black, White 2 foot Plastic Wire Raceway – Field cuttable – Includes wire channel with double faced tape and cover...

12V enclosed dimmable driver to be used with Nora Lighting’s 12 Volt systems. Features Wattage: 60W  Input Voltage: 120-277V Output Voltage: 12V...

24V plug-in driver to be used with Nora Lighting’s 24 Volt systems. Direct connection to a wall outlet. Features Wattage: 24W  Input Voltage: AC ...

Controlador LED enchufable de 24 V y 45 W Características Acabado: Blanco Potencia: 45W Voltaje de entrada: 120 V Voltaje de salida: 2...

Controlador LED enchufable de 24 V y 96 W con clasificación de clase II Características Acabado: Blanco Potencia: 96W Voltaje de entrada...

Se requiere un controlador RF para las tiras de luz LED RGBW o CCT. Se instala entre el controlador y el interconector de la línea de alimentación....

Se utiliza para programar luces de cinta RGBW o CCT con ciertas configuraciones de color. El control remoto se puede usar a una distancia de hasta ...

4′ Shallow recessed channel to mount low voltage tape lights flush with surface. Features Finish: Aluminum Aluminum extrusion Field cuttable Rece...

4′ Shallow Channel to mount low voltage tape light on a surface. Features Finish: Aluminum, Black, White Aluminum extrusion Field cuttable Surface...

4′ Deep recessed channel to mount low voltage tape lights flush with surface. Features Finish: Aluminum Aluminum extrusion Field cuttable Recessed...

4′ Deep Channel to mount low voltage tape light on a surface. Features Finish: Aluminum, White Aluminum extrusion Field cuttable Surface mount ins...

4′ J-Style channel to mount low voltage tape light on a surface indirectly. Features Finish: Aluminum Aluminum extrusion Field cuttable Surface mo...

4′ Corner channel to mount low voltage tape light in the corner to aim at 45°. Features Finish: Aluminum, Black, White Aluminum extrusion Field cu...

4′ Deep recessed channel to mount 120V tape light flush with surface. Features Finish: Aluminum Aluminum extrusion Field cuttable Recessed instal...

4′ Deep Channel to mount 120V tape light on a surface. Features Finish: Aluminum, White Aluminum extrusion Field cuttable Surface mount installati...

Surge Protector for 120V LED Tape Light. Recommended when installed outdoors or longer run lengths. Compatible with hardwire tape light only. Featu...

Pair of two mounting clips for 120V LED Tape Light. Each 12″ section of tape light includes two mounting clips. Features Sold in pack of 2 Two Mou...

NEXUS simplifica los sistemas de iluminación LED al combinar un regulador de intensidad LED de pared y una fuente de alimentación en una sola unida...

NEXUS simplifies LED array lighting systems by combining an in-wall LED dimmer switch and power supply into a single integrated unit. NEXUS mounts ...

4′ Shallow recessed channel to mount low voltage tape lights flush with surface. Features Finish: Aluminum Field cuttable Recessed installation I...

4′ Shallow channel to mount low voltage tape lights to flat surface. Features Finish: Aluminum Field cuttable Includes diffused lens, end caps a...

4′ Deep recessed channel to mount low voltage tape light flush with surface. Features Finish: Aluminum Field cuttable Recessed installation Inclu...

4′ Deep channel to mount low voltage tape light to flat surface. Features Finish: Aluminum Field cuttable Surface mount installation Includes dif...

4′ Trimless recessed channel to mount low voltage tape lights flush with the surface. Features Finish: White Field cuttable Includes diffused len...

L Connector connects two COB LED tape lights together at a 90° angle. Easily insert the tape light section into the connector without any tools nee...

T Connector connects three COB LED tape lights together. Easily insert the tape light section into the connectors without any tools needed. Feature...

X Connector connects four COB LED tape lights together. Easily insert the tape light section into the connectors without any tools needed. Features...

A 3″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed...

A 6" Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed...

The end-to-end connector connects two RGBW COB LED tape lights seamlessly. Maximum run length for tape light is 16.4′. Features Connects two tape ...

Cable de 12″ utilizado para cablear la luz de cinta LED COB RGBW a un controlador RGBW o decodificador DMX compatible. Cinta compatible: Tira ...

(15) Clear mounting clips and screws to mount RGBW tape light to flat surface. Note: Pack of 32 are included with each RGBW COB LED Tape Light Roll...

A 18″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools neede...

A 36″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools neede...

A 72″ Linking cable connects two RGBW COB LED tape lights together. Easily insert the tape light section into the connector without any tools neede...

A linking cable connects two COB LED tape lights together. Easily insert the tape light section into the connector without any tools needed. Featur...